鸭王,在线免费看_ -|五角星形├九寨沟科教局
淘宝减肥药排行榜十强
只推淘宝安全有效的减肥药

当前位置:鸭王,在线免费看 > 减肥产品

鸭王,在线免费看

时间:2020-06-24 10:41  编辑:北川高中

鸭王,在线免费看

MC78L00A Series,NCV78L00A

100 mA Positive Voltage Regulators

The MC78L00A Series of positive voltage regulators are inexpensive, easy−to−use devices suitable for a multitude of applications that require a regulated supply of up to 100 mA. Like their higher powered MC7800 and MC78M00 Series cousins, these regulators feature internal current limiting and thermal shutdown making them remarkably rugged. No external components are required with the MC78L00 devices in many applications.

These devices offer a substantial performance advantage over the traditional zener diode−resistor combination, as output impedance and quiescent current are substantially reduced.

Features

•Wide Range of Available, Fixed Output Voltages •Low Cost

•Internal Short Circuit Current Limiting •Internal Thermal Overload Protection •No External Components Required

•Complementary Negative Regulators Offered (MC79L00A Series)•Pb−Free Packages are Available

NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes

Figure 1. Representative Schematic Diagram

Figure 2. Standard Application

A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0 V above the output voltage even during the low point on the input ripple voltage.

*C in is required if regulator is located an appreciable distance from power supply filter.

**C O is not needed for stability; however, it does improve transient response.

Input

C 0.33m O **

Output TO−92P SUFFIX CASE 029

See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet.

ORDERING INFORMATION

Pin:1. Output

2. Ground

3. Input

PIN CONNECTIONS

(T op View)

V OUT GND GND V IN GND NC

GND NC SOIC−8*D SUFFIX CASE 751

*SOIC−8 is an internally modified SO−8 package. Pins 2, 3, 6, and 7 are electrically common to the die attach flag. This internal lead frame modification decreases package thermal resistance and increases power dissipation capability when appropriately mounted on a printed circuit board. SOIC−8 conforms to all exter-nal dimensions of the standard SO−8 package.

See general marking information in the device marking section on page 13 of this data sheet.

DEVICE MARKING INFORMATION

1

http://onsemi.com

(not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected.

ELECTRICAL CHARACTERISTICS (V I = 10 V, I O = 40 mA, C I = 0.33 m F, C O = 0.1 m F, −40°C < T J < +125°C (for MC78LXXAB, < +125°C (for MC78LXXAC), unless otherwise noted.)

NCV78L05A), 0°C < T

site and change control.

ELECTRICAL CHARACTERISTICS (V I = 15 V, I O = 40 mA, C I = 0.33 m F, C O = 0.1 m F, −40°C < T J < +125°C (for MC78LXXAB),°C < T < +125°C (for MC78LXXAC), unless otherwise noted.)

ELECTRICAL CHARACTERISTICS (V I = 23 V, I O = 40 mA, C I = 0.33 m F, C O = 0.1 m F, −40°C < T J < +125°C (for MC78LXXAB),

C < T < +125°C (for MC78LXXAC), unless otherwise noted.)

P D , P O W E R D I S S I P A T I O N (m W )

I I B , I N P U T B I A S C U R R E N T (m A )

I I B , I N P U T B I A S C U R R E N T (m A )

V O , O U T P U T V O L T A G E (V )

Figure 3. Dropout Characteristics

Figure 4. Dropout Voltage versus

Junction Temperature

Figure 6. Input Bias Current

versus Input Voltage

Figure 7. Maximum Average Power Dissipation versus

Ambient Temperature − TO−92 Type Package V I , INPUT VOLTAGE (V)

, I I O T J , JUNCTION TEMPERATURE (°C)

25

5075100

125

−V V V I , INPUT VOLTAGE (V)

0 5.010

152025303540

T A , AMBIENT TEMPERATURE (°C)

25

50

75100125

150

8.06.0

4.0

2.0

5.04.03.02.01.00

30

5070901101301500.40.8

1.21.6

2.02.4

2.80

20

3050

40

10

L, LENGTH OF COPPER (mm)

170 3.2

P D R , T H E R M A L R E S I S T A N C E J A θJ U N C T I O N -T O -A I R ( C /W )

°, M A X I M U M P O W E R D I S S I P A T I O N (W )

Figure 8. SOIC−8 Thermal Resistance and Maximum Power Dissipation versus P .C.B. Copper Length

APPLICATIONS INFORMATION

Design Considerations

The MC78L00A Series of fixed voltage regulators are designed with Thermal Overload Protection that shuts down the circuit when subjected to an excessive power overload condition. Internal Short Circuit Protection limits the maximum current the circuit will pass.

In many low current applications, compensation capacitors are not required. However, it is recommended that the regulator input be bypassed with a capacitor if the regulator is connected to the power supply filter with long wire lengths, or if the output load capacitance is large. The

input bypass capacitor should be selected to provide good high−frequency characteristics to insure stable operation under all load conditions. A 0.33 m F or larger tantalum,mylar, or other capacitor having low internal impedance at high frequencies should be chosen. The bypass capacitor should be mounted with the shortest possible leads directly across the regulators input terminals. Good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. Bypassing the output is also recommended.

Figure 9. Current Regulator

50 I Input 0.33+V O −V O

Figure 11. Positive and Negative Regulator

low high

control.

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our T ape and Reel Packaging

Specifications Brochure, BRD8011/D.

Specifications Brochure, BRD8011/D.

low high

control.

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our T ape and Reel Packaging

Specifications Brochure, BRD8011/D.

Specifications Brochure, BRD8011/D.

SOIC−8D SUFFIX CASE 751

xx = 05, 08, 09, 12, or 15

A = Assembly Location L = Wafer Lot Y = Year

W = Work Week

B, C

= T emperature Range

MARKING DIAGRAMS

MC78L zzABP ALYWW

zz = 05, 08, 09, 12, 15, 18 or 24A = Assembly Location L = Wafer Lot Y = Year

WW

= Work Week

TO−92P SUFFIX CASE 029

MC78L zzACP ALYWW

123123

PACKAGE DIMENSIONS

TO−92 (TO−226)

P SUFFIX CASE 29−11ISSUE AL

NOTES:

1.DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 198

2.

2.CONTROLLING DIMENSION: INCH.

3.CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED.

4.LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM.

PLANE

DIM

MIN MAX MIN MAX MILLIMETERS

INCHES A 0.1750.205 4.45 5.20B 0.1700.210 4.32 5.33C 0.1250.165 3.18 4.19D 0.0160.0210.4070.533G 0.0450.055 1.15 1.39H 0.0950.105 2.42 2.66J 0.0150.0200.390.50K 0.500−−−12.70−−−L 0.250−−− 6.35−−−N 0.0800.105 2.04 2.66P −−−0.100−−− 2.54R 0.115−−− 2.93−−−V

0.135−−−

3.43−−−

SOIC−8 NB D SUFFIX CASE 751−07ISSUE AB

ǒmm inches

ǓSCALE 6:1

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and Mounting T echniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

NOTES:

1.DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 198

2.

2.CONTROLLING DIMENSION: MILLIMETER.

3.DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION.

4.MAXIMUM MOLD PROTRUSION 0.15 (0.006)PER SIDE.

5.DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR

PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION.

6.751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−0

7.

DIM A MIN MAX MIN MAX INCHES 4.80 5.000.1890.197MILLIMETERS B 3.80 4.000.1500.157C 1.35 1.750.0530.069D 0.330.510.0130.020G 1.27 BSC 0.050 BSC H 0.100.250.0040.010J 0.190.250.0070.010K 0.40 1.270.0160.050M 0 8 0 8 N 0.250.500.0100.020S

5.80

6.200.2280.244

Y

M

0.25 (0.010)

Z S

X

S

____

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.

SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION

猜你喜欢

最安全有效的减肥药

最安全有效的减肥药

编辑:小徐

现在的减肥药真的是真假难分,在选择减肥药的同时也应该更加小心,减肥药多种多样,那么如何才能选择最安全有效的减肥药,也成了很多小仙女的内心疑问,下面就跟着鸭王,在线免费看小编一起看一下,如何选择最安全有效的减肥药。 最安全有效的减肥药选购方法 1、首先需要观察产品的外包装,在包装中可以看到其配方是不是含有激素,含有激素的减肥药对身体的内..

吃减肥药失眠

吃减肥药失眠

编辑:小徐

随着现在流行以瘦为美,很多人会不顾身体的健康选择减肥药,达到快速减肥瘦身的效果,但是很多减肥药都是有副作用的,副作用比较轻的就是失眠现象,那么吃减肥药出现失眠是怎么回事儿?如果出现失眠后,我们应该怎样缓解? 吃减肥药失眠是怎么回事 减肥药中富含安非他命,所以减肥药服用了太多会有失眠现象,服用减肥药期间,身体会逐渐出现抗药性,身..

最新文章